AUG and MSAR Trigger Improvements

The AUG has a notoriously bad trigger. Not only is the trigger pull about 10 pounds, but it is also very “sticky.” Some people just shrug and say, “bullpups have bad triggers.” That’s not necessarily so. For example, Kel-Tec’s RFB has a crisp 6.5-pound trigger right out of the box. I will explain the origin of the AUG’s bad trigger as well as steps that can be taken to improve it.

The original AUG was an infantry rifle with a clever select-fire mechanism: Pull the trigger partly to the rear for a single shot. Squeeze it all the way to the rear and the gun fires a fully-automatic burst. For this feature to be reliable in the field the AUG was designed with a long and heavy trigger to avoid unintentional full-auto discharges. Perhaps compounding this design decision is the fact that militaries have not historically made “trigger feel” a high priority for infantry rifles; if anything a heavy trigger is considered a safety feature that reduces the possibility of unintentional discharges.

Steyr did not consider it worthwhile to create a smoother or lighter trigger for their semi-automatic-only trigger packs.

MSAR, which specifically built its rifle for the U.S. civilian market, doesn’t have a good excuse for copying the heavy AUG trigger spring.

One easy way to improve these triggers is to lighten the Trigger Spring (Part 13). Unfortunately this is a complicated piece — you can’t just snip a few coils from it — and nobody manufactures a replacement spring that’s any lighter.

Trigger Tamer

A few years ago Ben Langlotz realized that you can lighten the Trigger Spring by reducing the installed tension. He invented a clever device called the Trigger Tamer that replaces the standard Bolt Retaining Lock (Part 12) and engages the Trigger Spring at a higher angle. This part is covered by patent #7,165,352. The patent protection also explains how he can charge up to $60 for a cut piece of Delrin plastic. The following image shows a trigger pack with the Trigger Tamer installed on the left and a standard trigger pack on the right.

The function of the Trigger Spring is twofold: It presses against the Disconnect Lever (Part 10), providing almost all of the resistance to the trigger when the hammer isn’t cocked. In the standard trigger pack this sets the uncocked trigger weight at 5 pounds; with the Trigger Tamer that falls to 2 pounds. But the Trigger Spring also presses against the Bolt Retaining Lock, which keeps the Bolt Retaining Pin from sliding out and the back of the rifle from falling apart. The standard trigger pack applies 10 pounds of force against the Bolt Retaining Lock; the Trigger Tamer reduces this to no more than 5 pounds. The sample Trigger Tamer I received had a rough finish and was unable to return the Bolt Retaining Lock under so little spring force until I sanded both sides smooth with 400-grit paper.

After I installed the Trigger Tamer in my AUG the trigger pull was more than 3 pounds lighter, going from about 9 pounds to under 6. It was also substantially smoother.

Neu-Trigger

Matt Mikhail realized that a much of the “stickiness” in the trigger pull is the result of plastic-on-plastic friction, and further that the most significant source of friction is the pressure of the cocked hammer against the “sear” (i.e., the bridge of the Trigger Slide). Because the hammer is so light (being made of plastic) the Hammer Springs must be very heavy to ensure the hammer hits the firing pin with enough force to reliably ignite primers. Matt cut and bent a small tab of thin steel to wrap around the sear, producing a metal-on-plastic interface at this high-pressure sticking point. He sells this as the Neu-Trigger. He has applied for a patent and is currently charging $27 for the piece, shown installed on my MSAR trigger pack here:

I tested a Neu-Trigger and found that it not only smooths out the action considerably but also reduces the trigger weight by about 1.5 pounds. It’s not always a drop-in part: The corners of AUG sears sometimes need to be cleaned up for it to fit; MSAR hammer faces need to be sanded down in order to function with it installed. Nevertheless it’s a clever device that shows the shortcomings of plastic triggers!

Lubrication

Of course there is a lot of other plastic-on-plastic friction involved in the trigger action of the AUG. Note that it is important not to use any petroleum-based lubricants here since they could dissolve or weaken the plastic. I tried lubricating the numerous contact points of the Trigger Slide with molybdenum disulfide but was unable to measure any significant effect on the trigger pull. Ben Langlotz sends three pages of instructions with his Trigger Tamer for disassembling, polishing, and lubricating the trigger pack and trigger bars. While these only reduce the trigger weight by a few ounces he claims they substantially smooth out the trigger action.

At this point I am hoping for someone to bring to market:

  1. A Trigger Spring 3 pounds lighter than the current standard.
  2. A metallic “match-grade” trigger pack where all critical interfaces can be held to higher tolerances, polished, and lubricated to produce a trigger pull as light and smooth as we can get on any other quality rifle.

[2012 Update: For the best trigger improvement see the new RAT WORX Hybrid Trigger Mod.]

13 thoughts on “AUG and MSAR Trigger Improvements

  1. Pingback: EmptorMaven » Blog Archive » Steyr AUG/A3 USA

  2. Pingback: EmptorMaven » Blog Archive » Kel-Tec RFB .308 Bullpup

  3. KenAgain

    There are rumors that someone will be bringing a new trigger pack for the entire range of AUG A3s, MSARS and TPD AXR rifles to market within the next month or two. I am thinking that it will involve either stainless steel parts or a lightened trigger/hammer spring.

  4. Matt

    rat worx has released their new trigger pack, which actually uses parts from an AR-15, the hybrid trigger mod.

  5. Pingback: EmptorMaven » Blog Archive » RAT WORX Hybrid Trigger Mod: The Best AUG Trigger

  6. federalist Post author

    It’s as safe as either of them separately. I tried that but the benefit didn’t seem to be as great as the sum of the parts. At this point I’d seriously recommend the Hybrid Trigger Mod; Neu-Trigger and Trigger Tamer are just overpriced band-aids.

  7. john

    I want to retain the original trigger pack, plus it is a cheaper band aid than getting the rat worx trigger pack. I’d rather spend the rest of the money on other accessories (shell deflector, charging handle, 42rnd mags, better extractor, rail, Viridian X5L or a Surefire light) and ammo.

  8. styx

    Just called today to order the Hybrid Trigger Mod….. I was quoted a 12-14 MONTH wait. My name is on the list. If you had to pick one of the other Mods which would it be. I just retried my AUG USR trigger (it’s been a while). There is really no creep, a crisp break, but a heavy pull. With that in mind I’m leaning towards the trigger tamer for the reduced pull as it feels fairly smooth as is. What do you think?

  9. federalist Post author

    If you can’t wait for the HTM then, especially given that you’re not feeling sticking or stacking, Trigger Tamer is your best option.

Leave a Reply

Your email address will not be published. Required fields are marked *